The following information is gleaned from TargetTalk:
Since no one has responded with
information on removing the breech
block from your CM84e,
perhaps the instructions for doing that on a Morini CM80 will be of some
assistance. As you intimated, the breech
block and firing pin in a Martini action are
probably "run of the mill" items. Since the CM80 is the predecessor of the CM84,
it might be that the design of the breech
block and firing pin was carried over into the
CM84e.
From the CM80 instruction manual (with my comments in brackets):
DISASSEMBLY
Open fully the armament lever and bring it to a semi-closed position. (The
armament lever is also called the Clamp Lever in the parts list and is the lever
to open the action and cock the firing pin.) Unscrew the fastening screw on the
grip and remove the firing mechanism. (Basically, remove the grip - which on the
CM80 contains the firing mechanism or trigger assembly.) Remove the pin and
remove the obturator. (The pin is the obturator pivot pin and the obturator is
the breech block.
The firing pin is retained within the breech
block.)
ASSEMBLY
To assemble the obturator ensure that the firing pin is loaded. (Make sure the
firing pin is cocked before pinning the breech
block back into the frame.) To assemble the grip,
introduce the sliding plate and stop it by bringing the armament lever in the
fully-opened position. (The CM80 has a grip that pivots in the vertical plane to
provide some adjustment in rake. So this latter instruction might not be quite
applicable to the CM84e. Basically, put the grip
back on the gun, having regard to the positioning of the armament lever/clamp
lever/cocking lever relative to the cocking lug on the firing pin.)
So basically, it looks like you cock the firing pin, remove the grip in order to
disassociate the firing mechanism from the firing pin, then drive out the
breech block pivot
pin and lift the breech
block out of the frame. The position of the cocking lever is important, but
if it is in the wrong position the breech
block won't come out. Same with reassembly - the
firing pin must be cocked and the cocking lever needs to be in the right
position to permit the breech
block to enter the frame.
Now it is entirely possible that the CM84e is
totally unlike the CM80 in respect to breech
block disassembly, but have a close look at your
CM84e to see if there is enough similarity for the
CM80 instructions to be helpful.
Hoping this is useful.
Regards,
Mike T.
-------------------------------
Mike Taylor always does his very best
to help folks and is very, very close to being "right on the money". I'll do my
best to detail the disassembly/assembly steps in CM84 terms. I'll assume you
have the owner's manual that came with the pistol. If not it's downloadable in .pdf
format from the Morini website.
Breach Block Removal:
1) Remove electronics and grip
2) Remove complete trigger assembly by removing screw 084099 accessible throught
he hole in trigger guard and by drifting out the rear-most small-diameter pin
084056. Now that you have the trigger assembly in your hand, use a soft-bristled
brush to remove all the priming compound and other gritty stuff that ends up
sitting on the top of the trigger assembly
3) Fully cycle the action to ensure mainspring is cocked.
4) Partially raise the cocking lever 084012 to ensure the breach
block is not fully locked in the closed position.
5) Drive out the pin 084015 holding the breach block
in position. Note that in the half dozen or so pistols I've taken apart they all
seem to like to have the pin drifted out from left to right.
6) Drive pin 084015 holding the cocking lever out from left to right, but only
about 1/2 - 1cm as it only needs to clear the thickness of the cocking lever.
7) Breach block and cocking lever should now be
ready to be removed through the top of the receiver.
Breach Block Disassembly:
1) Place breach block with its face down against a
block of hardwood and depress the sear lever,
allowing the firing pin to move fully forward to strike the hardwood (better
than a dry-fire which is about the only way you can break one of these firing
pins, according to Francesco).
2) Close to the rear of the block you'll find a
through-hole which passes through the mainspring retainer plug 084030. Take the
smallest hex key that came with the pistol (the one for adjusting the trigger
weight) and insert its longest arm completely through the through-hole in the
block. This hex key will now retain the retainer
plug, mainspring and firing pin as you proceed with disassembly.
3) Remove two Torx screws from tension block
084021 and remove tension block, being VERY
CAREFUL not to lose the plunger 084019 and plunger spring 084020.
4) Use your thumb to apply heavy pressure to the mainspring retainer plug,
relieving pressure on the hex key holding it in place. Remove the hex key and
slowly allow the mainspring to push the retainer plug from its recess in the
breach block.
5) Remove mainspring 084029 and firing pin, 084028.
Cleaning:
I won't get into specifics here, but I will caution that heavy accumulations of
crud, gunk and other undesireable substances will be found in the channel in
which the firing pin slides. A cotton swab soaked in solvent followed by a
tight-fitting cotton cloth on a wooden dowel is what i use to get all this
nonsense out of the hole. You'll also want to clean the firing pin hole in the
breach face.
One other area needing attention is in and around the sear mechanism. The sear
itself 084033 and its return spring 084034 will be well encrusted in dirt. A
toothbrush and solvent work well to clean this area, but be careful not to snag
the spring and yank it from its hole. It's small and hard to find on the floor!
(Been there, done that!) Also note that both the sear and the sear trip lever
084032 are pinned into the breach block using pins
riding in close-tolerance holes. Unless you need to replace the sear, don't even
try to move these pins. They're TIGHT and only drift one way out of the breach
block (they drift from right to left, or from the
smooth side of the block to the side that is
machined to allow the cocking lever to move).
Since you've got the pistol apart you'll also want to pay serious attention to
de-gunking the extractor 084009 and its return spring 084010, as well as to
cleaning the recess in the breach which accomodates the rim of the cartridge
case. Build up of contaminants in this recess can lead to misfires.
Re-assembly:
Re-assembly is just the opposite of disassembly. Keep in mind that you won't be
able to get it all put together unless you cock the mainspring first. I use a
hardwood dowel to push on the firing pin; this methodology avoids leaving
unsightly scratches on the metal.
If you need more details than this explanation offers, don't hesitate to post
back here and I'll do my best to help out.
Mark.